欢迎访问苏州丰硕自动化设备秒速快3
产品中心
联系我们
    苏州丰硕自动化设备秒速快3
    苏州
    电  话:
    0512-66300668/66557556
    手  机: 13912610668/13913176973
    Email: lgr720707@126.com
    地  址: 苏州市吴中区临湖镇联东路718号
       
    成都  
    手  机: 13912610668
    电  话: 028-87535191
    Email: lghbylp@163.com
    地  址: 成都市高新区天府一街1399号
       
    网  址: www.ididntcomeheretodie.com
       
       
     

  • 双门连体烘箱
  • 2016-03-10 16:44:54
  • \
    烘箱采用国家重点推广的节能环保加热新技术,通过电源使电热管加热,产生热源,当它被加热物体吸收时可直接转变为热能,从而获得快速干燥效果,达到缩短生产周期,节约能源,提高产品质量等目的。
        结构
      烘箱箱体由角钢、薄钢板制成。外壳与工作室间填充玻璃纤维保温与隔热。加热系统装置在工作室的顶部。水平式循环通风,使之箱内的温度更加均匀,本型烘干箱能有效的避免工作室内存在的梯度温差及温度过冲现象,且能提高工作室内的温度均匀性。
        温度控制
      采用智能程序温控仪控温,PID参数自整定,固态继电器调功率,无触点连续调节,自动完成烘干全过程,能满足任何固化曲线的要求,操作简便,性能可靠。配用热敏元件探头组成自动恒温控制。控温精度灵敏,室温~300℃任意选择设定。工作室内温度可以从仪表直接读出。恒温时间可达99.99H
    烘箱分类
    烘箱根据性能可分为可编程烘烤箱、精密烘箱充氮烘箱、真空烘箱、防爆烘箱、电热鼓风干燥箱,热风循环烘箱等。方泛适用于各行各业需要烘干加热的元器件。   烘箱按行业来分可分为:电子行业专用烘箱 仪器仪表行业专用烘箱 塑料及橡胶行业专用烘箱 电工器材行业专用烘箱 电镀行业专用烘箱 印刷行业专用烘箱 眼镜行业专用烘箱 制药行业专用烘箱 纺织印染行业专用烘箱 机械行业专用烘箱 合成纤维行业专用烘箱 木材行业专用烘箱 摩擦材料专用烘箱 ...   烘箱按外形来分可分为:卧式烘箱和立式烘箱两种   烘箱以额定温度区分,一般可分为:   低温烘箱:100℃以下,一般用于电气产品老化,普通料件的缓速干燥,部分食品原料、塑料等产品的干燥用。   常温烘箱:100-250℃,这是最常见的使用温度,用于大多数料件的水分干燥、涂层固化、加温、加热、保温等。   高温烘箱:250-400℃,高温干燥特种材料、工件加温安装、材料高温试验、化工原料的反应处理等。   超高温烘箱:400-600℃,更高的工作温度,高温干燥特种材料、工件加温热处理、材料高温试验等   烘箱送风方式分类及各自适用性:   烘箱送风方式分为水平送风和垂直送风。   水平送风:适用于需放置在托盘中烘烤的物件;水品送风的热风是由工作室两边吹出的,所以可以沐浴在托盘中的物件!烘烤效果会很好。相反,放置在托盘中烘烤的物件用垂直送风是很不适宜的,垂直送风热风是由上而下吹出,它会把热风挡住,从而热风沐浴不到下面几层,相应烘烤效果会很差!   垂直送风:适用于烘烤放置在网架上的物件,垂直送风热风是由上而下吹出,由于是网架,真个上下流通性会很好,使得热风可完全沐浴在物件上!   当然,放置在网架上的物件也可用水平送风,这可要看物件本身的特性了!   为了使读者了解烘箱更多,特编辑了烘箱的具体尺寸,一般可根据自己要烘烤的物料来选择尺寸,在定制烘箱时,只要告诉生产厂家你要烘烤的物料的特征及一次的烘烤量,厂家就会给你推荐一款合适的烘箱。当然,自己了解烘箱的具体尺寸后,那你也可以自己核算,直接告诉烘箱生产厂家你要什么尺寸的烘箱,那样就不会浪费厂家给你报价的时间!
    烘箱使用注意事项
      烘箱是利用电热丝隔层加热使物体干燥的设备。它适用于比室温高5~300℃(有的高200℃)范围的烘培、干燥、热处理等,灵敏度通常为±1℃。烘箱的型号很多,但基本结构相似,一般由箱体、电热系统和自动控温系统三部分组成。其使用及注意事项总结如下:1.烘箱应安放在室内干燥和水平处,防止振动和腐蚀。引2.要注意安全用电,根据烘箱耗电功率安装足够容量的电源闸刀。选用足够的电源导线,并应有良好的接地线。3.带有电接点水银温度计式温控器的烘箱应将电接点温度计的两根导线分别接至箱顶的两个接线柱上。另将一支普通水银温度计插入排气阀中,(排气阀中的温度计是用来校对电接点水银温度计和观察箱内实际温度用的)打开排气阀的孔。调节电接点水银温度计至所需温度后紧固钢帽上的螺丝,以达到恒温的目的。但必须注意调节时切勿将指示铁旋至刻度尺外。4.当一切准备工作就绪后方可将试品放入烘箱内,然后连接并开启电源,红色指示灯亮表示箱内已加热。当温度达到所控温度时,红灯熄灭绿灯亮,开始恒温。为了防止温控失灵,还必须照看。5.放入试品时应注意排列不能太密。散热板上不应放试品,以免影响热气流向上流动。禁止烘焙易燃、易爆、易挥发及有腐蚀性的物品。6.当需要观察工作室内样品情况时,可开启外道箱门,透过玻璃门观察。但箱门以尽量少开为好,以免影响恒温。特别是当工作在200℃以上时,开启箱门有可能使玻璃门骤冷而破裂。7.有鼓风的烘箱,在加热和恒温的过程中必须将鼓风机开启,否则影响工作室温度的均匀性和损坏加热元件。8.工作完毕后应及时切断电源,确保安全。9.烘箱内外要保持干净。10.使用时,温度不要超过烘箱的最高使用温度。11.为防止烫伤,取放试品时要用专门工具。


    Oven heating by the national key promotion of energy conservation and environmental protection new technology, make through power supply heating, electric heating tube produce heat source, when it is absorbed by the heated object can be converted into heat energy, thereby gaining rapid drying effect, to shorten the production cycle, save energy, improve product quality, etc.

    structure

    Oven body made of Angle steel, steel sheet. Between the shell and studio filled glass fiber heat preservation and heat insulation. The top of the heating systems in the studio. Horizontal circulation ventilation, the temperature in the cabinet is more even, this type of drying box can effectively avoid indoor work existence the gradient of temperature difference and temperature overshoot phenomenon, and can improve the work of indoor temperature uniformity.

    The temperature control

    Intelligent temperature controller, temperature control program PID parameter self-tuning, solid state relay power, non-contact continuous adjustment, automatic drying process, can meet the requirements of any curing curve, simple operation, reliable in performance. Automatic constant temperature control with temperature sensor probe. Sensitive accuracy of temperature control, select any set at room temperature to 300 ℃. Indoor temperature can work from the meter direct reading. Constant temperature time of 99.99 H

    Classification of oven

    Oven according to the performance can be divided into programmable baking boxes, precision oven nitrogen oven, vacuum oven, explosion-proof drying oven, electric drum wind drying oven, hot air circulation drying oven, etc。 The pan is suitable for all walks of life need drying heating components。 Drying oven according to the industry to points can be divided into: electronic industry dedicated oven instrumentation industry dedicated oven plastic and rubber industry dedicated oven dedicated oven electrical equipment industry Electroplating industry dedicated oven Special printing industry dedicated oven drying oven glasses industry The pharmaceutical industry dedicated oven Textile printing and dyeing industry dedicated oven Machinery industry special dedicated oven oven synthetic fiber industry Wood industry dedicated oven friction materials dedicated oven。。。 Drying oven according to shape points can be divided into: horizontal oven and vertical oven two kinds With rated temperature oven, generally can be divided into: low temperature oven: under 100 ℃, commonly used in electrical products aging, slow drying of ordinary materials and some food raw materials, plastic products such as drying。 Room temperature oven: 100-100 ℃, which is the most common use temperature, moisture dry for most materials, curing coating, heating, heating, heat preservation, etc。 High temperature oven: 250-400 ℃, high temperature drying of special material, workpiece heating installation, high temperature test, the reaction of chemical raw materials processing, etc。 Ultra high temperature oven: 400-400 ℃, the higher the working temperature, high temperature drying of special material, workpiece heating heat treatment, high temperature test, etc Oven air supply system classification and their applicability: the oven is divided into horizontal supply and vertical air supply air supply manner。 Horizontal air supply: suitable for objects to be placed on the tray bake; Water product supply hot air is blown out by the studio on both sides, so the objects can be basked in the tray! Bake the effect will be very good。 Instead, placed on the tray bake objects with vertical air supply is not suitable, vertical supply air blow out hot air is top-down, it blocked the hot air, thus hot bath is less than the following several layers, corresponding to bake the effect will be poor! Vertical air supply: suitable for baking placed on the rack, the objects on the vertical supply air blow out hot air is top-down, because it is a rack, whole and liquidity will be very good, make the hot air can be completely bathed in them! Placed on a rack items, of course, also can use horizontal air supply, it depends on the characteristics of the object itself! In order to make readers know more about baking oven, editor of the size of the oven, generally can choose according to their own to baking material size, the custom oven, just tell the manufacturer you want to bake the characteristics of the material and a baking capacity, manufacturer will give you recommend a suitable drying oven。 , of course, you know the dimensions of a baking oven, after that you can own accounting, directly tell oven manufacturer what you want the size of the oven, so don't waste time to manufacturer to quote you!

    Oven use matters needing attention

    Oven is the use of electric heating wire object dry interlayer heating equipment. It is suitable for higher than room temperature of 5 ~ 300 ℃ (200 ℃) and high range of baking, drying, heat treatment, etc., the sensitivity is usually + / - 1 ℃. Type of oven is many, but the basic structure similar to that of general by enclosure, electric heating system and automatic temperature control system of three parts. Its use and the matters needing attention summed up as follows: 1. The oven shall be placed in a dry indoor and level, to prevent vibration and corrosion. Lead 2. Pay attention to safety electricity, according to the oven consumes power installed capacity of power supply knife. Use enough power supply wire, and should be good grounding line. 3. With electric contact mercury thermometer thermostat oven should be the two wire of electric contact thermometer separately connected to two terminal on the top of the box. The other will be a ordinary mercury thermometer inserted into the exhaust valve, (in the exhaust valve thermometer is used for calibration of electric contact mercury thermometer and observe the actual temperature in the oven) to open the exhaust valve hole. Adjusting the electric point mercury thermometer to the required temperature after fastening screws on the steel cap, in order to achieve the purpose of constant temperature. Never will but must pay attention to regulating indicate the iron screw to the scale. 4. When the sample (s) only after all preparations were made to put in the oven, then open the power supply and connection, the red indicator has been heated in the oven. When the temperature reaches the temperature controlled by a red light green light out, began to constant temperature. In order to prevent temperature control failure, must also take care of. 5. The sample (s) into the arrangement should be paid attention to when not too close. The sample (s) should not be put on the cooling plate, lest affect hot air to flow in. Ban the baking inflammable, explosive, volatile and corrosive goods. 6. When you need to observe work indoor sample, but the door is open the heretics, through the glass door, to observe. But with less as far as possible to open the door for good, lest affect a constant temperature. Especially when work at above 200 ℃, the door is open could make glass door quenching and rupture. 7. There are drum wind drying oven, in the process of heating and constant temperature blower must be open, otherwise affect the workshop temperature uniformity and damage the heating elements. 8. Should be promptly cut off the power supply after work, to ensure safety. 9. The oven inside and outside to keep it clean. 10. When used, the temperature is not more than the highest use temperature of the oven. 11. In order to prevent burns, try to use a special tool.

上一篇   |   下一篇

扫一扫,添加好友

在线客服
湖南快乐十分开户 福建快3网址 秒速飞艇注册 秒速快三注册 福建11选5走势 秒速快三注册 秒速飞艇是真的吗 湖南快乐十分计划 秒速飞艇玩法 湖南快乐十分开奖